MINI factory OEM replacement oil filter base & cover w/filter. This is the newer design Without the cage & spring. For the 1st generation MINI Cooper & S models with automatic transmission including 2002-2006 R50 & R53 Hardtop and 2005-2008 R52 Convertible
OEM Oil Filter Housing Auto Transmission MINI Cooper Cooper S R50 R52 R53 Gen1
MINI Factory OEM replacement oil filter base & cover (w/filter). This unit is the newer design WITHOUT the troublesome cage & spring. Includes the entire housing with filter and sensor. Also includes gaskets for the housing cover and between the base and block.
Fits the following models:
2002-2006 R50 MINI Cooper non-S Hardtop (all transmissions) 2002-2006 R53 MINI Cooper S Hardtop with Automatic transmission
2005-2008 R52 MINI Cooper non-S Convertible (all transmissions) 2005-2008 R52 MINI Cooper S Convertibles with Automatic transmission
All Cooper models, or Cooper S models with Automatic Transmission.
If you have an early MINI built before 07/2004, take a look at this article regarding the different oil cannister cover design.
For the 3 bolts that attach the Housing to the Block, use the following Torque: 30 Nm (22 lb-ft) on the W10 engine (Cooper non-S) 25 Nm (18 lb-ft) on the W11 engine (Cooper S)
NOTE: The hole at the bottom of the oil filter will appear much smaller than the shaft in the filter base - this is NORMAL and CORRECT. If you press the filter into the base, the hole will 'stretch' over the shaft. This is a design feature to ensure a tight seal so the oil does not bypass the filter.
MINI Factory OEM replacement oil filter housing (with base cover & filter) for manual transmission. For the 1st generation MINI Cooper S models including 2002-2006 R53 Hardtop and 2005-2008 R52 Convertible.
OEM Oil Filter Housing Manual Transmission MINI Cooper S R52 R53 Gen1OEM Oil Filter Housing Manual Transmission MINI Cooper S R52 R53 Gen1
MINI factory OEM replacement oil filter base & cover (w/filter). Includes the entire housing with filter and sensor. Also includes gaskets (and O-rings) for the housing cover, oil cooler, and between the base and block.
Fits the following Cooper S models:
2002-2006 R53 MINI Cooper S Hardtop with manual transmission 2005-2008 R52 MINI Cooper S Convertible with manual transmission
Includes the base, cover, filter, gasket, oil pressure switch and the oil cooler module.
NOTE: The hole at the bottom of the oil filter will appear much smaller than the shaft in the filter base - this is NORMAL and CORRECT. If you press the filter into the base, the hole will 'stretch' over the shaft. This is a design feature to ensure a tight seal so the oil does not bypass the filter.
Factory replacement oil filter base & cover (w/filter). This unit is the newer design WITHOUT the troublesome cage & spring.
Fits the following models:
2002-2006 R50 MINI Cooper Hatchback (all transmssions) 2002-2006 R53 MINI Cooper S Hatchback WITH Automtic transmission
2005-2008 R52 MINI Cooper Convertible (all transmssions) 2005-2008 R52 MINI Cooper S Convertibles WITH Automtic transmission
All Cooper models, or Cooper S models with Automatic Transmission.
The MINI factory has discontinued the fully assembled housing, so we are supplying all of the individual pieces to make up the same identical housing at the same price - all MINI factory original parts. Includes the base, cover, o-ring, filter, gasket and oil pressure switch.
Install the filter with the black plastic ring 'down' into the housing. Torque the cover to oil filter housing to 25Nm or 18 ft-lb.
Install the Oil Pressure Warning Switch into the housing at 20Nm or 15 ft-lb. (The factory uses a sealant on the threads).
For the 3 bolts that attach the Housing to the Block, use the following Torque: 30 Nm (22 lb-ft) on the W10 engine (Cooper non-S) 25 Nm (18 lb-ft) on the W11 engine (Cooper S)
NOTE: The hole at the bottom of the oil filter will appear much smaller than the shaft in the filter base - this is NORMAL and CORRECT. If you press the filter into the base, the hole will 'stretch' over the shaft. This is a design feature to ensure a tight seal so the oil does not bypass the filter.
MINI Factory OEM replacement oil filter base & cover (w/filter). This unit is the newer design WITHOUT the troublesome cage & spring. Includes the entire housing with filter and sensor. Also includes gaskets for the housing cover and between the base and block.
Fits the following models:
2002-2006 R50 MINI Cooper non-S Hardtop (all transmissions) 2002-2006 R53 MINI Cooper S Hardtop with Automatic transmission
2005-2008 R52 MINI Cooper non-S Convertible (all transmissions) 2005-2008 R52 MINI Cooper S Convertibles with Automatic transmission
All Cooper models, or Cooper S models with Automatic Transmission.
If you have an early MINI built before 07/2004, take a look at this article regarding the different oil cannister cover design.
For the 3 bolts that attach the Housing to the Block, use the following Torque: 30 Nm (22 lb-ft) on the W10 engine (Cooper non-S) 25 Nm (18 lb-ft) on the W11 engine (Cooper S)
NOTE: The hole at the bottom of the oil filter will appear much smaller than the shaft in the filter base - this is NORMAL and CORRECT. If you press the filter into the base, the hole will 'stretch' over the shaft. This is a design feature to ensure a tight seal so the oil does not bypass the filter.
The early MINI with production dates up to 07/2004 has a couple extra pieces inside the oil filter cannister cover - a spring and plastic cage. These items were eliminated on the later models after 07/2004. This article explains the differences and what to do if you lose some of these parts.
Your E-Mail and/or password are incorrect. Please try again.
Note: As of Oct 15th 2020, you must use your e-mail address, not your username. Passwords are also case-sentive.
If you continue to have problems click on the Help Icon for additional options.
Login with your E-Mail Address. If you would like your login information reset, click on the button below to request your login information to be reset.