Not Logged In
Recently Viewed Items
Your Price $9.27
You save: $10.68
Part No: NME1051
36mm 3/8 drive Socket for removing Oil Filter Cartridge. The MINI oil filter cannister is positioned on the back of the engine with very little clearance to the firewall. You need a very low profile socket like this one in order loosen and remove the filter cannister.
Fits 2002 - 2006 R50/R53 MINI Cooper and Cooper S. Also fits 2007-2008 R52 MINI Cooper and Cooper S Convertibles.
Does NOT fit 2007+ R56 Hardtops.
Filter change tips: Use this 36mm socket with a ratchet to remove the canister. It helps to 'loosen' the canister a bit when you drain the oil to help drain the filter (for less mess). Make sure you replace the o-ring with the new one supplied with the filter - apply a coat of fresh oil on the o-ring when you install it and tighten the filter housing to 18 ft. lbs.
Remember to use sythetic motor oil. MINI recommends 5W-40 or 5W-30 FULL SYNTHETIC motor oil.
Tighten the drain plug to 18 ft-lb. Start the engine and check for oil pressure. Don't forget to check for leaks too!
And darn it, dispose of the used oil and filter properly, please. And wipe that oil off the driveway before you track it into the house!
To reset the oil change interval in your MINI, see oil service reset.
Oil Change Tip & Hints - R50/52/53 Cooper & S
Additional Related Articles:
Helpful Hints for changing the oil...
Frequently, the cannister cover will be very difficult to break free. Use a breaker bar with CAUTION! You may need a 'low profile' socket due to the limited space available.
If you loosen the filter cannister cover enough to break the seal, it will help drain the oil from the filter as you drain the oil pan. Less mess later!
When replacing the O-ring, save the old one just in case (will explain later).
When replacing the O-ring on the cannister cover, make sure you lubricate the O-ring with PLENTY of fresh oil before you install it, and lubricate again after it is in place. If you fail to do this, the O-ring will bunch up and cause a leak!
The new oil filter should be 'pre-seated' into the base and cover before installation. Take the filter (plastic side down) and press firmly into the base until it is fully seated. Remove and do the same into the cannister cover. This reduces the resistance from initial seating. You can leave the filter seated into the cover and screw the cover back onto the base, or you can leave the filter in the base fully seated and screw the cover back onto the base.
Getting the Cannister Cover started into the base is a little tricky - having the O-ring well lubricated will make it a little easier. Start the cover onto the base carefully, confirming the cover is 'square' with the base to prevent cross-threading. Once you have it started, you will still have resistance from the new O-ring, but you should be able to get the cover well onto the base by hand.
Torque the cannister cover to 18 lb-ft.
The factory Drain Plug gasket is a plastic gasket that is molded into the Drain Plug. Best to replace the drain plug at every oil change. The cost is minimal compared to headaches from a leaky plug! (The linked filter part numbers above includes a new drain plug.)
Torque the Drain Plug to 18 lb-ft as well.
You can also use a magnetic drain plug that will help trap microscopic metal debris and can be re-used.
Fill with a name brand FULL SYNTHETIC motor oil. It should take close to 4 quarts. MINI recommends oils in SAE classes 5W-40 and 5W-30. MINI likes Castrol Synthetic, many MINI owners use Mobile 1 Synthetic.
After you confirm everything is buttoned up, and you have fresh oil in the engine, start the engine. The red Engine Oil Pressure warning light should go off in a couple seconds. After a running the engine for 30 seconds or so, shut off the engine and let sit for a few minutes. Check for leaks, and re-check the oil level. If everything is dry and the dip stock shows 'full' - go for a drive!
If you run the car and find a puddle of oil under the engine, there is a good chance the O-ring was damaged when you installed the cannister cover. Take the old O-ring that you saved, and re-install - with care!
To reset the oil service reminder, see this article .