SLiME Tire Sealant is formulated and tested for use in all pneumatic tires. Once installed, SLiME remains liquid and will not harden or dry out. Slime is guaranteed for 2 years.
As the SLiME treated tire rotates, centrifugal force pushes the sealant to the tread area creating a layer of protection, repairing punctures as they occur or treating existing punctures. SLiME is not intended for use in tires losing pressure from sidewall punctures, bead leaks, damaged rims or faulty valves. SLiME is recommended as a repair only in high speed, over-the-road tires.
· Repairs punctures up to ¼” (6mm) using Fibro-Seal™ technology.
· Remains liquid inside the tire, coating the tread area as the tire rotates.
· Non-toxic, non-hazardous, non-flammable, non-aerosol and water soluble.
· Contains rust and corrosion inhibitors to maintain the integrity of the rim.
· TPMS friendly (Note: May not install easily into tires with direct or valve mounted devices).
· Tires treated with SLiME can be cleaned out with water allowing for the installation of a proper plug/patch.
· SLiME for tubeless tires can also be installed into tubeless bike tires. SLiME installs between the rim and the tire bead. Hold the bead open with two tire levers, install, and re-inflate with a fast burst of air to seat the bead to the rim.
· SLiME has a freeze point of -30ºF (-34.4ºC) and a boiling point of 220ºF (104.4ºC).
What is Fibro-Seal Technology? SLiME utilizes a state-of-the-art blend of environmentally friendly fibers, binders, polymers and proprietary congealing agents which intertwine and clot within the puncture. This Fibro-Seal lattice, together with the viscous transportation system (the “green” goo) seeks out and tightly packs itself into the puncture, preventing and repairing flats with a flexible long lasting plug.
Note: SLiME is not recommended for use in tires mounted on chrome wheels.
TPMS STATEMENT OF COMPATIBILITY
As leaders in the tire care and repair industry, Accessories Marketing, Incorporated (AMI), the manufacturers of SLiME Tire Sealant wish to address the mandate set forth in the Transportation Recall Enhancement, Accountability and Documentation (TREAD) Act, passed in the fall of 2000. In response to this mandate, the National Highway Traffic Safety Administration (NHTSA) established the Federal Motor Vehicle Safety Standard that requires the installation of Tire Pressure Monitoring Systems (TPMS) to all vehicles by September 1, 2007.
From our findings, and after significant dialog with the leading manufacturers of TPMS devices, SLiME Tire Sealant will not damage TPMS devices. We understand TPMS manufacturers have conducted extensive testing to ensure their sensors remain operational after exposure to any chemical fluids that might come into contact with the sensors. This includes after market products, such as SLiME Tire Sealant. AMI has also conducted independent testing, which supports and verifies SLiME Tire Sealant’s compatibility with TPMS devices.
Currently, there are two types of TPMS devices available: Direct and Indirect. SLiME Tire Sealant’s TPMS formulation is compatible with all TPMS systems. However, it is important to note that once installed, Slime Tire Sealant may come in contact with the sensor in a way that renders the sensor TEMPORARILY inoperable until it is properly cleaned, inspected and re-installed by a tire care professional.
Because SLiME is a water soluble flat repair treatment, it is easily removed from the tire with water. At the time the affected tire is inspected by a tire care professional, they should clean the sealant from the tire, prepare the area and repair with a Rubber Manufacturer’s Association (RMA) approved patch/plug. The TPMS device should also be cleaned off with water to remove any sealant which may have come into contact with the device. Do not use any fine objects to ream and clean the small pressure sensor opening as it may damage the electronics. After the repaired tire is replaced and inflated the TPMS system will resume operating as normal.
Please note that SLiME is recommended as a REPAIR for all Over the Road (OTR) applications.