Mini Mania
Est. 1974
Shop by Car
 Live Help
800-946-2642
Search
All
Your Price $99.95
Qty:
Flash2pass Integrated Garage Door Opener - Mini Cooper & S

Flash2pass Integrated Garage Door Opener - Mini Cooper & S

Flash2pass Integrated Garage Door Opener - Mini Cooper & S

Flash2pass Integrated Garage Door Opener - Mini Cooper & S

Flash2pass Integrated Garage Door Opener - Mini Cooper & S
Open your garage door or gate by flashing the brights on your MINI twice in succession. Eliminate the garage door opener remote from your car and never fumble around looking for it!

The Flash2Pass™ consist of the new, second generation, patented Flash2Pass™ transmitter installed your MINI, and its corresponding receiver installed in your garage. A double flash of your headlight high beams opens or closes your garage door. The digitally encrypted signal and rolling code technology gives you the ultimate in security, and keeps strangers out of your garage. Up to six transmitters may be used to operate a single receiver, and additional receivers may be installed elsewhere and programmed to your Flash2Pass™ equipped vehicle. A small one-time investment gets you the maintenance free system, with no remote transmitter to get lost or stolen. Flash2Pass™ gets its power from your car, so you will never need to replace any batteries. Works with cars, trucks, motorcycles, tractors and riding mowers with a 12v electrical system, and virtually any garage door opener manufactured since 1982. Quick and easy do-it-yourself installation.

Technical Information:
Flash2Pass™ Installation for MINI

Flash 2 Pass Garage Gate Opener Instructions - Mini Mania Inc.Flash2Pass™ Installation

The Flash2Pass™ transmitter and receiver are designed as a do-it-yourself installation. It is very simple and straight forward if you follow the instructions included in every set. If you purchase a separate Flash2Pass™ transmitter or receiver, instructions are not only included for installation but also for programming the transmitter/s to the receiver/s.

Transmitter installation in a car

The Flash2Pass™ transmitter is mounted under the hood of your car near one of the headlights. One wire from the transmitter will be attached to the headlight high beam positive wire, and the other transmitter wire will be attached to the headlight high beam negative (ground) wire. It doesn't matter which transmitter wire is attached to which headlight wire as the transmitter is non-polarized, which means it figures that out itself. The wires are attached with Posi-Tap™ connectors that do no harm to your vehicle's wiring. No wires are cut, they're just tapped into. This allows the transmitter to be removed when the vehicle is sold or traded in, and the transmitter can be attached under the hood with a plastic zip tie, which means the tie can be cut to remove the transmitter.

Individual Vehicle Installation Guide

BMW Mini Cooper

Tap the Brown (ground) wire and yellow with a blue trace or the yellow with a green trace, depending on whether you're mounting it on the driver's side or passenger side. Zip tie the transmitter in place behind the headlight assembly and check the clearance before you close the hood (bonnet). You can use some Play-doh or a piece of cheese on the transmitter to make sure you have the room.

It appears that models with Xenon headlights use the white wire as the high beam hot, not the yellow wire. The brown ground wire remains the same.

 

Transmitter installation on a motorcycle

Installation of the Flash2Pass™ transmitter on a motorcycle is very simple. Depending on the model of motorcycle, the easiest way to do it is to remove the headlight from the bucket as if you were changing the bulb, and connect the transmitter, as described above in the car installation. Then just tuck the transmitter into the bucket and reinstall the headlight. Again, this may not be applicable to every installation, but it is a general rule of thumb. Click on Motorcycle Installation Guide below, for more information.

Let InstallerNet install the transmitter for you!

Remember, if you are not comfortable installing the transmitter yourself, we have partnered with InstallerNet to bring you more than 1500 installaton centers nationwide that will install the transmitter in your vehicle for a set fee of only $39.95.
Click here or on the InstallerNet logo to find an installer in your area

Receiver

The Flash2Pass™ receiver is even easier to install. There are two wires that go from the garage door opener motor to a pushbutton on the wall that you use to open the garage door from the inside. After disconnecting the power to the garage door opener, you will remove the pushbutton from the wall, undo the two wires from the back and attach them to the Flash2Pass™ receiver, and attach the receiver to the wall. Turn the power back on, and that's it!

If your current pushbutton console has functions other than to open the door, like light and lock switches, you can still keep those functions by using "jumper" wires from your current console to the Flash2Pass™ receiver. Complete instructions are included with every set and separate receiver.

Motorcycle/Scooter Installation Guide

Make Year Model Notes
BMW All All Tap the brown wire and the white wire or the white with a colored trace.
Bombardier All Can Am Spyder

Click here to find illustrated instructions in PDF format 

Buell All except below All except below Single high/low with 3 wire connector. Tap the 2 outside wires.
  2003 984cc Lightening Separate high beam with 2 wire connector. Tap each wire.
Harley-Davidson All except below All except below Single high/low with 3 wire connector. Tap the 2 outside wires. Should be the black and the white wires.
  2002-03 V-Rod Separate high beam with 2 wire connector. Tap each wire.
Honda All except below All except below Single high/low with 3 wire connector. Tap the 2 outside wires.
  2001-03 Gold Wing Remove the right glove box to access the back of the high beam lamp. Find the 2 wire connector at the back of the lamp, and tap each wire.
  2001-03 RC51 Separate high beam with 2 wire connector. Tap each wire.
  2001 RVT1000R Separate high beam with 2 wire connector. Tap each wire.
  2002-03 CBR954RR Separate high beam with 2 wire connector. Tap each wire.
  2001 CBR929RR Separate high beam with 2 wire connector. Tap each wire.
  2001-03 CBR600F Separate high beam with 2 wire connector. Tap each wire.
Kawasaki All except below All except below Single high/low with 3 wire connector. Tap the 2 outside wires.
  2003 ZX-6R, ZX-6RR Ninja Separate high beam with 2 wire connector. Tap each wire.
Piaggio 2005 bv200 Open the glove box and remove the four screws holding the headlight assembly in place and pull the headlight clear. Place the transmitter in the left glove box and feed the two wires through the headlight high beam adjustment screw hole. Tap the purple and the black wires. Reassemble in reverse order.
Suzuki All except below All except below Single high/low with 3 wire connector. Tap the 2 outside wires.
  1999-2003 Hayabusa Separate high beam with 2 wire connector. Tap each wire.
Triumph All All Single high/low with 3 wire connector. Tap the 2 outside wires.
Yamaha All All Single high/low with 3 wire connector. Tap the 2 outside wires.

Read Full Article
Customer Reviews
Write a customer review
Review this item and receive a $5 coupon off you're next purchase!* Click Here For Details

Recently Viewed Items