× 1-800-946-2642 Home My Account Social / Forum Articles Contact My Cart
Shop Now
Select Your Car Type Sale Items Clearance Items New Items
MINI Factory replacement Twin Scroll Turbocharger for Cooper S models (non-JCW) with the N18 engine. If you need to replace your turbo, this is the MINI factory replacement unit.  Street Legal in California and other states as a 'factory original replacement unit'. 

Fits the following Cooper S models with the N18 engine:

2011-2013 R56 MINI Cooper S Hardtop
2011-2014 R55 MINI Cooper S Clubman
2011-2015 R57 MINI Cooper S Convertible
2012-2015 R58 MINI Cooper S Coupe
2012-2015 R59 MINI Cooper S Roadster
2011-2016 R60 MINI Cooper S Countryman
2013-2016 R60 MINI Cooper S Paceman

See the Turbo Application Guide to see all the options for replacement and upgraded Turbo's.

For Turbo related replacement hardware, see our Mini Cooper Turbo Installation Hardware Application Guide.

OTHER PARTS TO CONSIDER

Gaskets, seals, studs, and other hardware are NOT included. If you need to replace these items, order separately.

See our Turbo Install Kit. This kit includes all the most commonly replaced gaskets and seals, plus a new oil supply line. Additional gaskets, seals and other hardware may be required depending on the installation.

When servicing the Turbo on the MINI, it is very important (maybe even critical) that you replace the Turbo Oil Supply line to avoid potential future turbo issues.   (Included in the Turbo Install Kit).

Over time, the turbo and turbo supply line builds a fine layer of 'coked' or cooked oil on the internal surfaces. When you remove the supply line from the turbo, this disrupts the continuity of the coked layer with great potential of some of the coking to flake free. These coked oil particles can easily clog the fine journals that feed oil to the turbo bearings. Once the the oil flow is compromised, it is only a matter of time for cascading failures that can damage the turbo and catalytic converter! Don't take a chance - REPLACE the Oil Supply Line ! ! ! 

For additional protection, take a look at the Turbo Oil Supply Line Thermal Wrap.

For other TURBOCHARGER related products, see our TURBOCHARGER products page.

OUR ADVICE ON DRIVING A TURBOCHARGED MINI

We STRONGLY recommend you change the motor oil more frequently than the factory recommendation. Anecdotal evidence suggests Turbo's with more frequent oil changes have fewer issues. We suggest 5000 mile oil change interval or less. Make sure you use FULL SYNTHETIC motor oil with the ACEA (Association des Constructeurs Europeens d'Automobiles) A3/B3 specification.

After a long or hard drive, drive 'easy' for a while just before your destination. This will reduce the engine and oil temperatures to lower operating levels. Also make a habit to let the engine idle for a couple minutes before shutting off. This will help cool the turbo preventing oil coking in the journals and bearings. Yes, the MINI has an auxiliary water pump that runs after shutdown to help cool the turbo, BUT - the oil isn't cirulating - it just sits there waiting for the turbo to cool. This is why we recommend you idle before shutdown - let the oil circulate while the temperature comes down.

MANUFACTURER NOTES ON INSTALLATION:

[ ] Always replace the turbo oil supply line with the turbo.
- - - Due to excess heat round the turbocharger and particulates suspended in the turbo supply oil the oil will harden or "coke~ in the turbo and oil supply lines. If the oil supplyline is not replaced with the turbocharger the coked oil will break free from the side walls of the oil supply line and damage the turbocharger bearings. Cleaning the oil line will not help and only aggravate and increase the likelihood of the turbo failure due to coked oil breaking free form the sidewall.

[ ] Always replace the catalytic converter on mini coopers before installing a new turbo.
- - - The Catalytic converter may look clear but if any oil leaked into it some of the holes might be blocked and will cause back pressure. This starts to happen on Mini Coopers at 15k miles! Exhaust back pressure causes premature failure of the turbocharger. Turbochargers are not designed to have pressure on the exhaust side.As an alternative, have your catalytic converter refurbished to restore original flow.

[ ] Always prime the turbocharger.
- - - No oil on the turbocharger bearings will cause failure of the bearings if they are dry even for a short period of time. For maximum protection, see Turbo Additive for Priming New Turbo's

[ ] Always flush oil after a turbocharger change
- - - Most turbochargers fail catastrophically this means that the metal and other items can end up in your oil. Always flush your oil a minimum of 3 times with new oil after an oil change.

LEARN MORE ABOUT TURBOCHARGERS:

Take a look at these informative videos that will help you avoid potential pitfalls with the Turbo:

How to Kill a New Turbo Part 1 - Oil Line

How to Kill a New Turbo Part 2 - Catalytic Converter

How to Kill a New Turbo Part 3 - No or Low Oil

How to Kill a New Turbo Part 4 - Using the Correct Oil

NOTE: The MINI Factory replacement such as this product will pass the California Emissions Visual inspection.

Genuine OEM Part Turbo N18 OEM Replacement | Gen2 Mini Cooper R55 R56 R57 R58 R59 R60 (2011-2016)

Turbo N18 OEM Replacement | Gen2 Mini Cooper R55 R56 R57 R58 R59 R60 (2011-2016)

Turbo N18 OEM Replacement | Gen2 Mini Cooper R55 R56 R57 R58 R59 R60 (2011-2016)
Selected: 2011-2016 Cooper S with N18 engine
Part No: G2NME2203
$2591.99
Qty:
This Item has a $200.00 core charge.
Fits the following:
MINI (2002-Current)
PayPal Pay Later
Alternate Products
TWIN SCROLL TURBOCHARGER BORG WARNER | Gen2 MINI COOPER S R55 R56 R57 R58 R59 R60 R61
$1294.52 TWIN SCROLL TURBOCHARGER BORG WARNER | Gen2 MINI COOPER S R55 R56 R57 R58 R59 R60 R61
Turbo Upgrade 40mm Refurbished | Gen2 MINI Cooper S & JCW R55 R56 R57 R58 R59 R60 R61
$889.33 Turbo Upgrade 40mm Refurbished | Gen2 MINI Cooper S & JCW R55 R56 R57 R58 R59 R60 R61

MINI Factory replacement Twin Scroll Turbocharger for JCW models with the N18 engine. If you need to replace your JCW turbocharger, this is the MINI factory replacement unit.  Street Legal in California and other states as a 'factory original replacement unit'. 

Fits the following JCW models with the N18 engine:

2012.5-2013 R56 JCW MINI Cooper S Hardtop
2012.5-2014 R55 JCW MINI Cooper S Clubman
2012.5-2015 R57 JCW MINI Cooper S Convertible
2012.5-2015 R58 JCW MINI Cooper S Coupe
2012.5-2015 R59 JCW MINI Cooper S Roadster
2012.5-2016 R60 JCW MINI Cooper S Countryman

See the Turbo Application Guide to see all the options for replacement and upgraded Turbo's.

For Turbo related replacement hardware, see our Mini Cooper Turbo Installation Hardware Application Guide.

OTHER PARTS TO CONSIDER

Gaskets, seals, studs, and other hardware are NOT included. If you need to replace these items, order separately.

See our Turbo Install Kit. This kit includes all the most commonly replaced gaskets and seals, plus a new oil supply line. Additional gaskets, seals and other hardware may be required depending on the installation.

When servicing the Turbo on the MINI, it is very important (maybe even critical) that you replace the Turbo Oil Supply line to avoid potential future turbo issues.   (Included in the Turbo Install Kit).

Over time, the turbo and turbo supply line builds a fine layer of 'coked' or cooked oil on the internal surfaces. When you remove the supply line from the turbo, this disrupts the continuity of the coked layer with great potential of some of the coking to flake free. These coked oil particles can easily clog the fine journals that feed oil to the turbo bearings. Once the the oil flow is compromised, it is only a matter of time for cascading failures that can damage the turbo and catalytic converter! Don't take a chance - REPLACE the Oil Supply Line ! ! ! 

For additional protection, take a look at the Turbo Oil Supply Line Thermal Wrap.

For other TURBOCHARGER related products, see our TURBOCHARGER products page.

OUR ADVICE ON DRIVING A TURBOCHARGED MINI

We STRONGLY recommend you change the motor oil more frequently than the factory recommendation. Anecdotal evidence suggests Turbo's with more frequent oil changes have fewer issues. We suggest 5000 mile oil change interval or less. Make sure you use FULL SYNTHETIC motor oil with the ACEA (Association des Constructeurs Europeens d'Automobiles) A3/B3 specification.

After a long or hard drive, drive 'easy' for a while just before your destination. This will reduce the engine and oil temperatures to lower operating levels. Also make a habit to let the engine idle for a couple minutes before shutting off. This will help cool the turbo preventing oil coking in the journals and bearings. Yes, the MINI has an auxiliary water pump that runs after shutdown to help cool the turbo, BUT - the oil isn't cirulating - it just sits there waiting for the turbo to cool. This is why we recommend you idle before shutdown - let the oil circulate while the temperature comes down.

MANUFACTURER NOTES ON INSTALLATION:

[  ] Always replace the turbo oil supply line with the turbo.
- - - Due to excess heat round the turbocharger and particulates suspended in the turbo supply oil the oil will harden or "coke~ in the turbo and oil supply lines. If the oil supplyline is not replaced with the turbocharger the coked oil will break free from the side walls of the oil supply line and damage the turbocharger bearings. Cleaning the oil line will not help and only aggravate and increase the likelihood of the turbo failure due to coked oil breaking free form the sidewall.

[  ] Always replace the catalytic converter on mini coopers before installing a new turbo.
- - - The Catalytic converter may look clear but if any oil leaked into it some of the holes might be blocked and will cause back pressure. This starts to happen on Mini Coopers at 15k miles! Exhaust back pressure causes premature failure of the turbocharger. Turbochargers are not designed to have pressure on the exhaust side.As an alternative, have your catalytic converter refurbished to restore original flow.

[  ] Always prime the turbocharger.
- - - No oil on the turbocharger bearings will cause failure of the bearings if they are dry even for a short period of time. For maximum protection, see Turbo Additive for Priming New Turbo's

[  ] Always flush oil after a turbocharger change
- - - Most turbochargers fail catastrophically this means that the metal and other items can end up in your oil. Always flush your oil a minimum of 3 times with new oil after an oil change.

LEARN MORE ABOUT TURBOCHARGERS:

Take a look at these informative videos that will help you avoid potential pitfalls with the Turbo:

How to Kill a New Turbo Part 1 - Oil Line

How to Kill a New Turbo Part 2 - Catalytic Converter

How to Kill a New Turbo Part 3 - No or Low Oil

How to Kill a New Turbo Part 4 - Using the Correct Oil

NOTE: The MINI Factory replacement such as this product will pass the California Emissions Visual inspection.

MINI Factory replacement Twin Scroll Turbocharger for your Mini Cooper S models with the N14 engine. If you need to replace your turbocharger, this is the MINI factory replacement unit.  Street Legal in California and other states as a 'factory original replacement unit'.

Fits the following models with the N14 engine:

2007 up to 05/2009 R56 MINI Cooper S Hatchback
2008 up to 05/2009 R55 MINI Cooper S Clubman
2009 up to 05/2009 R57 MINI Cooper S Convertible

See the Turbo Application Guide to see all the options for replacement and upgraded Turbo's.

For Turbo related replacement hardware, see our Mini Cooper Turbo Installation Hardware Application Guide.

OTHER PARTS TO CONSIDER

Gaskets, seals, studs, and other hardware are NOT included. If you need to replace these items, order separately.

See our Turbo Install Kit. This kit includes all the most commonly replaced gaskets and seals, plus a new oil supply line. Additional gaskets, seals and other hardware may be required depending on the installation.

When servicing the Turbo on the MINI, it is very important (maybe even critical) that you replace the Turbo Oil Supply line to avoid potential future turbo issues.   (Included in the Turbo Install Kit).

Over time, the turbo and turbo supply line builds a fine layer of 'coked' or cooked oil on the internal surfaces. When you remove the supply line from the turbo, this disrupts the continuity of the coked layer with great potential of some of the coking to flake free. These coked oil particles can easily clog the fine journals that feed oil to the turbo bearings. Once the the oil flow is compromised, it is only a matter of time for cascading failures that can damage the turbo and catalytic converter! Don't take a chance - REPLACE the Oil Supply Line ! ! ! 

For additional protection, take a look at the Turbo Oil Supply Line Thermal Wrap.

For other TURBOCHARGER related products, see our TURBOCHARGER products page.

OUR ADVICE ON DRIVING A TURBOCHARGED MINI

We STRONGLY recommend you change the motor oil more frequently than the factory recommendation. Anecdotal evidence suggests Turbo's with more frequent oil changes have fewer issues. We suggest 5000 mile oil change interval or less. Make sure you use FULL SYNTHETIC motor oil with the ACEA (Association des Constructeurs Europeens d'Automobiles) A3/B3 specification.

After a long or hard drive, drive 'easy' for a while just before your destination. This will reduce the engine and oil temperatures to lower operating levels. Also make a habit to let the engine idle for a couple minutes before shutting off. This will help cool the turbo preventing oil coking in the journals and bearings. Yes, the MINI has an auxiliary water pump that runs after shutdown to help cool the turbo, BUT - the oil isn't cirulating - it just sits there waiting for the turbo to cool. This is why we recommend you idle before shutdown - let the oil circulate while the temperature comes down.

NOTES ON INSTALLATION:

[ ] Always replace the turbo oil supply line with the turbo.
- - - Due to excess heat round the turbocharger and particulates suspended in the turbo supply oil the oil will harden or "coke~ in the turbo and oil supply lines. If the oil supplyline is not replaced with the turbocharger the coked oil will break free from the side walls of the oil supply line and damage the turbocharger bearings. Cleaning the oil line will not help and only aggravate and increase the likelihood of the turbo failure due to coked oil breaking free form the sidewall.

[ ] Always replace the catalytic converter on mini coopers before installing a new turbo.
- - - The Catalytic converter may look clear but if any oil leaked into it some of the holes might be blocked and will cause back pressure. This starts to happen on Mini Coopers at 15k miles! Exhaust back pressure causes premature failure of the turbocharger. Turbochargers are not designed to have pressure on the exhaust side.As an alternative, have your catalytic converter refurbished to restore original flow.

[ ] Always prime the turbocharger.
- - - No oil on the turbocharger bearings will cause failure of the bearings if they are dry even for a short period of time. For maximum protection, see Turbo Additive for Priming New Turbo's

[ ] Always flush oil after a turbocharger change
- - - Most turbochargers fail catastrophically this means that the metal and other items can end up in your oil. Always flush your oil a minimum of 3 times with new oil after an oil change.

LEARN MORE ABOUT TURBOCHARGERS:

Take a look at these informative videos that will help you avoid potential pitfalls with the Turbo:

How to Kill a New Turbo Part 1 - Oil Line

How to Kill a New Turbo Part 2 - Catalytic Converter

How to Kill a New Turbo Part 3 - No or Low Oil

How to Kill a New Turbo Part 4 - Using the Correct Oil

NOTE: The MINI Factory replacement such as this product will pass the California Emissions Visual inspection.

MINI Factory replacement Twin Scroll Turbocharger for JCW models with the N14 engine. If you need to replace your JCW turbocharger, this is the MINI factory replacement unit.  Street Legal in California and other states as a 'factory original replacement unit'.

Fits the following JCW models with the N14 engine:

11/2007 up to 2012.5 R55 JCW MINI Cooper S CLUBMAN
11/2007 up to 2012.5 R56 JCW MINI Cooper S Hatchback
08/2008 up to 2012.5 R57 JCW MINI Cooper S Convertible

See the Turbo Application Guide to see all the options for replacement and upgraded Turbo's.

For Turbo related replacement hardware, see our Mini Cooper Turbo Installation Hardware Application Guide.

OTHER PARTS TO CONSIDER

Gaskets, seals, studs, and other hardware are NOT included. If you need to replace these items, order separately.

See our Turbo Install Kit. This kit includes all the most commonly replaced gaskets and seals, plus a new oil supply line. Additional gaskets, seals and other hardware may be required depending on the installation.

When servicing the Turbo on the MINI, it is very important (maybe even critical) that you replace the Turbo Oil Supply line to avoid potential future turbo issues.   (Included in the Turbo Install Kit).

Over time, the turbo and turbo supply line builds a fine layer of 'coked' or cooked oil on the internal surfaces. When you remove the supply line from the turbo, this disrupts the continuity of the coked layer with great potential of some of the coking to flake free. These coked oil particles can easily clog the fine journals that feed oil to the turbo bearings. Once the the oil flow is compromised, it is only a matter of time for cascading failures that can damage the turbo and catalytic converter! Don't take a chance - REPLACE the Oil Supply Line ! ! ! 

For additional protection, take a look at the Turbo Oil Supply Line Thermal Wrap.

For other TURBOCHARGER related products, see our TURBOCHARGER products page.

OUR ADVICE ON DRIVING A TURBOCHARGED MINI

We STRONGLY recommend you change the motor oil more frequently than the factory recommendation. Anecdotal evidence suggests Turbo's with more frequent oil changes have fewer issues. We suggest 5000 mile oil change interval or less. Make sure you use FULL SYNTHETIC motor oil with the ACEA (Association des Constructeurs Europeens d'Automobiles) A3/B3 specification.

After a long or hard drive, drive 'easy' for a while just before your destination. This will reduce the engine and oil temperatures to lower operating levels. Also make a habit to let the engine idle for a couple minutes before shutting off. This will help cool the turbo preventing oil coking in the journals and bearings. Yes, the MINI has an auxiliary water pump that runs after shutdown to help cool the turbo, BUT - the oil isn't cirulating - it just sits there waiting for the turbo to cool. This is why we recommend you idle before shutdown - let the oil circulate while the temperature comes down.

MANUFACTURER NOTES ON INSTALLATION:

[ ] Always replace the turbo oil supply line with the turbo.
- - - Due to excess heat round the turbocharger and particulates suspended in the turbo supply oil the oil will harden or "coke~ in the turbo and oil supply lines. If the oil supplyline is not replaced with the turbocharger the coked oil will break free from the side walls of the oil supply line and damage the turbocharger bearings. Cleaning the oil line will not help and only aggravate and increase the likelihood of the turbo failure due to coked oil breaking free form the sidewall.

[ ] Always replace the catalytic converter on mini coopers before installing a new turbo.
- - - The Catalytic converter may look clear but if any oil leaked into it some of the holes might be blocked and will cause back pressure. This starts to happen on Mini Coopers at 15k miles! Exhaust back pressure causes premature failure of the turbocharger. Turbochargers are not designed to have pressure on the exhaust side.As an alternative, have your catalytic converter refurbished to restore original flow.

[ ] Always prime the turbocharger.
- - - No oil on the turbocharger bearings will cause failure of the bearings if they are dry even for a short period of time. For maximum protection, see Turbo Additive for Priming New Turbo's

[ ] Always flush oil after a turbocharger change
- - - Most turbochargers fail catastrophically this means that the metal and other items can end up in your oil. Always flush your oil a minimum of 3 times with new oil after an oil change.

LEARN MORE ABOUT TURBOCHARGERS:

Take a look at these informative videos that will help you avoid potential pitfalls with the Turbo:

How to Kill a New Turbo Part 1 - Oil Line

How to Kill a New Turbo Part 2 - Catalytic Converter

How to Kill a New Turbo Part 3 - No or Low Oil

How to Kill a New Turbo Part 4 - Using the Correct Oil

NOTE: The MINI Factory replacement such as this product will pass the California Emissions Visual inspection.

MINI Factory replacement Twin Scroll Turbocharger for Cooper S models (non-JCW) with the N18 engine. If you need to replace your turbo, this is the MINI factory replacement unit.  Street Legal in California and other states as a 'factory original replacement unit'. 

Fits the following Cooper S models with the N18 engine:

2011-2013 R56 MINI Cooper S Hardtop
2011-2014 R55 MINI Cooper S Clubman
2011-2015 R57 MINI Cooper S Convertible
2012-2015 R58 MINI Cooper S Coupe
2012-2015 R59 MINI Cooper S Roadster
2011-2016 R60 MINI Cooper S Countryman
2013-2016 R60 MINI Cooper S Paceman

See the Turbo Application Guide to see all the options for replacement and upgraded Turbo's.

For Turbo related replacement hardware, see our Mini Cooper Turbo Installation Hardware Application Guide.

OTHER PARTS TO CONSIDER

Gaskets, seals, studs, and other hardware are NOT included. If you need to replace these items, order separately.

See our Turbo Install Kit. This kit includes all the most commonly replaced gaskets and seals, plus a new oil supply line. Additional gaskets, seals and other hardware may be required depending on the installation.

When servicing the Turbo on the MINI, it is very important (maybe even critical) that you replace the Turbo Oil Supply line to avoid potential future turbo issues.   (Included in the Turbo Install Kit).

Over time, the turbo and turbo supply line builds a fine layer of 'coked' or cooked oil on the internal surfaces. When you remove the supply line from the turbo, this disrupts the continuity of the coked layer with great potential of some of the coking to flake free. These coked oil particles can easily clog the fine journals that feed oil to the turbo bearings. Once the the oil flow is compromised, it is only a matter of time for cascading failures that can damage the turbo and catalytic converter! Don't take a chance - REPLACE the Oil Supply Line ! ! ! 

For additional protection, take a look at the Turbo Oil Supply Line Thermal Wrap.

For other TURBOCHARGER related products, see our TURBOCHARGER products page.

OUR ADVICE ON DRIVING A TURBOCHARGED MINI

We STRONGLY recommend you change the motor oil more frequently than the factory recommendation. Anecdotal evidence suggests Turbo's with more frequent oil changes have fewer issues. We suggest 5000 mile oil change interval or less. Make sure you use FULL SYNTHETIC motor oil with the ACEA (Association des Constructeurs Europeens d'Automobiles) A3/B3 specification.

After a long or hard drive, drive 'easy' for a while just before your destination. This will reduce the engine and oil temperatures to lower operating levels. Also make a habit to let the engine idle for a couple minutes before shutting off. This will help cool the turbo preventing oil coking in the journals and bearings. Yes, the MINI has an auxiliary water pump that runs after shutdown to help cool the turbo, BUT - the oil isn't cirulating - it just sits there waiting for the turbo to cool. This is why we recommend you idle before shutdown - let the oil circulate while the temperature comes down.

MANUFACTURER NOTES ON INSTALLATION:

[ ] Always replace the turbo oil supply line with the turbo.
- - - Due to excess heat round the turbocharger and particulates suspended in the turbo supply oil the oil will harden or "coke~ in the turbo and oil supply lines. If the oil supplyline is not replaced with the turbocharger the coked oil will break free from the side walls of the oil supply line and damage the turbocharger bearings. Cleaning the oil line will not help and only aggravate and increase the likelihood of the turbo failure due to coked oil breaking free form the sidewall.

[ ] Always replace the catalytic converter on mini coopers before installing a new turbo.
- - - The Catalytic converter may look clear but if any oil leaked into it some of the holes might be blocked and will cause back pressure. This starts to happen on Mini Coopers at 15k miles! Exhaust back pressure causes premature failure of the turbocharger. Turbochargers are not designed to have pressure on the exhaust side.As an alternative, have your catalytic converter refurbished to restore original flow.

[ ] Always prime the turbocharger.
- - - No oil on the turbocharger bearings will cause failure of the bearings if they are dry even for a short period of time. For maximum protection, see Turbo Additive for Priming New Turbo's

[ ] Always flush oil after a turbocharger change
- - - Most turbochargers fail catastrophically this means that the metal and other items can end up in your oil. Always flush your oil a minimum of 3 times with new oil after an oil change.

LEARN MORE ABOUT TURBOCHARGERS:

Take a look at these informative videos that will help you avoid potential pitfalls with the Turbo:

How to Kill a New Turbo Part 1 - Oil Line

How to Kill a New Turbo Part 2 - Catalytic Converter

How to Kill a New Turbo Part 3 - No or Low Oil

How to Kill a New Turbo Part 4 - Using the Correct Oil

NOTE: The MINI Factory replacement such as this product will pass the California Emissions Visual inspection.

Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Related Technical Articles:
Turbo Installation Hardware for your Gen2 Rxx MINI Cooper S
Created: March 18, 2016
Mini Cooper Turbo Installation hardware applications guide lists turbo related hardware you might need when you service the turbo
MINI Cooper Turbocharger Upgrade Technology
Created: July 03, 2013
Understanding Turbo Technologies involved in an 'upgraded' turbocharger and why they result in improved performance in your MINI Cooper.
SuperCharger Types
Created: September 21, 2010
MINI Cooper S engines from 2001 thru 2006 used Superchargers- here is an overview of the types of superchargers
R55 - R61 Turbo Replacement and Upgrade Options
Created: September 15, 2014
R55 to R61 Turbo Replacement and Upgrade Options from Mini Mania
Find the Right Turbo to Fit Your MINI Cooper S or JCW
Created: June 25, 2015
Browse our Mini Cooper Turbo Application Guide. When replacing a Turbo, there are many options to choose from. This chart shows which turbos are appropriate for the type of replacement and the applicable model years. It helps making finding your turbo easy.